Add the Elecrow CrowPanel 7.0" as a third board, and take the packages and the add-on from Gitea (0.2.93)

A board file for the Elecrow CrowPanel 7.0" (DIS08070H, ESP32-S3-WROOM-1-N4R8): 800x480 through mipi_rgb, GT911 on the
ESP32-S3's USB pins (elecrow_usb_phy.h frees them, behind a flag only this board sets), the Guition's vertical sizes
across a wider page, no rotation. Its 4 MB of flash take the CYD's budget: a partition table of the component's
(smart_display: partitions: 4mb_wide_slots, 1,984 KB slots), the icon fonts at 2 bits a pixel and the TLS client only
bring the firmware to 1,865,440 bytes, 91.8 % of a slot, with camera images kept. docs/ELECROW.md has the numbers and
the trade.

The add-on reads a large board's name from the type sensor's value, the editor offers the board under New screen and
draws the wide preview, tools/check.sh builds it with the budget, render_topbar and capture_ui take the panel's size.
Firmware 0.2.79; the CYD image is unchanged (1,633,760 bytes).

This fork builds from gittea.trippedonmy.name/Xandrossian/homeassistant_espscreen: the packages, the fonts, the
component and the add-on repository point there instead of GitHub.

components/smart_display/elecrow_usb_phy.h

@@ -0,0 +1,30 @@
+#pragma once
+// The Elecrow CrowPanel 7.0" wires its GT911 touch I2C to GPIO19 and GPIO20, the ESP32-S3's USB D- and D+. The ROM
+// leaves the USB_SERIAL_JTAG PHY on those pads, and ESP-IDF's I2C driver cannot take them back: the bus reads as
+// "I2C software timeout" and the touch never answers (esphome/esphome#15356, ESPHome 2026.3+). This runs before any
+// ESPHome component (a static constructor at priority 101): the PHY lets the pads go, and both become plain GPIOs
+// with their pull-ups, as the I2C driver expects to find them. The board's USB-C port is a CH340 on UART0, so nothing
+// is lost.
+//
+// ESPHome includes every header of the component in every build, so the code is behind a flag only the Elecrow's board
+// file sets (`-DESP_SCREENS_FREE_USB_PADS=1`, packages/boards/elecrow-crowpanel7.yaml): the CYD has no such peripheral,
+// and the Guition, an ESP32-S3 too, keeps its USB.
+#if defined(ESP_SCREENS_FREE_USB_PADS) && ESP_SCREENS_FREE_USB_PADS
+#include "hal/usb_serial_jtag_ll.h"
+#include "soc/io_mux_reg.h"
+#include "soc/usb_serial_jtag_reg.h"
+
+namespace elecrow {
+static __attribute__((constructor(101))) void release_usb_pads() {
+  usb_serial_jtag_ll_phy_enable_pad(false);
+  CLEAR_PERI_REG_MASK(USB_SERIAL_JTAG_CONF0_REG, USB_SERIAL_JTAG_USB_PAD_ENABLE);
+  CLEAR_PERI_REG_MASK(USB_SERIAL_JTAG_CONF0_REG, USB_SERIAL_JTAG_DP_PULLUP);
+  for (uint32_t reg : {IO_MUX_GPIO19_REG, IO_MUX_GPIO20_REG}) {
+    PIN_FUNC_SELECT(reg, PIN_FUNC_GPIO);
+    PIN_INPUT_ENABLE(reg);
+    REG_SET_BIT(reg, FUN_PU);
+    REG_CLR_BIT(reg, FUN_PD);
+  }
+}
+}  // namespace elecrow
+#endif