An alert from esp_screens_show_alert takes a `camera` (a camera.* or image.* entity): a Guition with firmware
0.2.57 shows that moment's picture across the top of the card, and a tap opens the camera full screen. A camera
or image tile opens the same full-screen view, refreshed every four seconds at a steady pace.
ESP Screen Manager fetches the snapshot with its own access, sizes it for the screen and serves a 24-bit BMP
under a random, short-lived link on port 8098; the screen loads it with ESPHome's online_image and holds no
Home Assistant token. BMP because ESPHome decodes it per chunk, where a full-screen JPEG held the loop 0.6 s.
The CYD keeps its alerts without the picture and gets no camera tiles.
The Guition also builds with ESPHome 2026.8+ again: backlight_fade.h derived from ESPHome's LEDC output, which
2026.8 made final, so the backlight now dims through ESPHome's own light transition.
Tested on the bench boards and a local add-on on the Home Assistant Yellow; docs/TEST_RESULTS_0266.md.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Wake from Home Assistant counted as a tap: it reset last_touch_ms, the one
clock that standby and Back to page 1 both read. An automation pressing Wake
on every motion therefore held an open card or page 2 up for as long as
someone moved in the room. Back to page 1 now has its own clock, last_use_ms,
written only by the boot, the touchscreen triggers, open_settings from Home
Assistant and the UI self test. Wake, an alert ending and Auto standby on
still restart the standby time, and Wake still brings back the brightness and
the second hand.
The rule moved from the interval into the script back_to_page_1_when_due.
Wake runs it right after waking a dimmed screen, so a page whose time ran out
during standby lights up on page 1 instead of jumping there a second later.
ESP Screens no longer opens the first screen by itself. Until one is picked
the page says "Choose a screen", and with no screens it still offers the
install; both cards start hidden so neither flashes while the page loads.
Checked with 48 host API checks per board, both ESP32 builds, 314 Python and
16 C++ tests, and the editor on the demo home. Firmware 0.2.56.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
One rule ends a Sleep: a tap, Wake or an alert. The Auto standby switch
cleared sleep_requested when Home Assistant turned standby off, while
ESP Screens and the settings page on the screen did not; now only
wake_display clears the flag, and apply_screen_settings still wakes a
screen the standby time dimmed.
dim_display no longer checks anything itself (the interval checks Auto
standby, the Sleep button sets the flag). It dims, then runs go_home with
"also on standby" on, otherwise closes the settings page and every card
through close_cards. Before, it copied half of go_home and hid the four
YAML overlays itself, so a runtime detail card stayed open under a dimmed
screen. close_cards is now the one runtime_tiles::dismiss() call: the
fallback and the widget.hide actions after its return ran for nothing.
The backlight light becomes internal. Home Assistant could change it, but
the minute tick put the level back, and switching it off darkened the
screen without standby. The brightness numbers and Wake/Sleep replace it.
A dead clock-label branch from the manual profile leaves
apply_screen_settings.
Checked with 209 Python and 14 C++ tests, host builds of both boards over
the native API, and ESP32 builds of both Easy profiles. Firmware 0.2.46.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Every screen gets two template buttons, Wake and Sleep, for automations
(button.press on button.<screen>_wake / _sleep). Wake does what a tap does:
a dimmed screen runs wake_display, a screen that is on only restarts the
standby count. Sleep dims right away through dim_display, also with Auto
standby off, and closes an alert that is up (reported as remote); it is
ignored during a touch calibration.
A new non-restored flag, sleep_requested, keeps that standby in place:
dim_display dims with standby off, and apply_screen_settings, which runs
every minute, no longer wakes such a screen. wake_display clears it (a tap,
Wake, an alert), and so does the Auto standby switch when it really turns
standby off. Nothing is saved, so the buttons cost no flash writes and may
run on every motion.
The Claude skill, README, add-on docs and RELEASING describe both buttons.
Checked on host builds of both boards over the native API, 24 checks each
(timer, Sleep with Auto standby off across a minute tick, alert,
calibration), and with ESP32 builds of both Easy profiles (+336 B RAM).
Firmware 0.2.45.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Max Gramser