Xandrossian
9857cc3bda
A board file for the Elecrow CrowPanel 7.0" (DIS08070H, ESP32-S3-WROOM-1-N4R8): 800x480 through mipi_rgb, GT911 on the ESP32-S3's USB pins (elecrow_usb_phy.h frees them, behind a flag only this board sets), the Guition's vertical sizes across a wider page, no rotation. Its 4 MB of flash take the CYD's budget: a partition table of the component's (smart_display: partitions: 4mb_wide_slots, 1,984 KB slots), the icon fonts at 2 bits a pixel and the TLS client only bring the firmware to 1,865,440 bytes, 91.8 % of a slot, with camera images kept. docs/ELECROW.md has the numbers and the trade. The add-on reads a large board's name from the type sensor's value, the editor offers the board under New screen and draws the wide preview, tools/check.sh builds it with the budget, render_topbar and capture_ui take the panel's size. Firmware 0.2.79; the CYD image is unchanged (1,633,760 bytes). This fork builds from gittea.trippedonmy.name/Xandrossian/homeassistant_espscreen: the packages, the fonts, the component and the add-on repository point there instead of GitHub.
108 lines
7.6 KiB
Markdown
108 lines
7.6 KiB
Markdown
# Elecrow CrowPanel 7.0" — 800 × 480
|
||
|
||
The **Elecrow CrowPanel ESP32 HMI 7.0-inch** (product code **DIS08070H**, hardware V2.0 and V3.0) has a board file of
|
||
its own, next to the CYD's and the Guition's: an 800 × 480 IPS panel on the ESP32-S3's own RGB bus, **GT911
|
||
capacitive touch**, an **ESP32-S3-WROOM-1-N4R8** with 4 MB of flash and 8 MB of octal PSRAM, and a backlight on
|
||
GPIO 2. It is the Guition's kind of screen, a big RGB panel with capacitive touch, in a wider, landscape form: every
|
||
card, the camera images and album covers, the page swipe from the glass edge, the settings on the screen. Two things
|
||
differ in kind, and both are below: the **4 MB of flash** (the CYD's budget, not the Guition's 16 MB) and a panel
|
||
that is not square, so it **does not turn** (no Rotation entity).
|
||
|
||
Hardware source: [Elecrow's wiki](https://www.elecrow.com/wiki/esp32-display-702727-intelligent-touch-screen-wi-fi26ble-800480-hmi-display.html)
|
||
and the [ESPHome devices page for the CrowPanel 7.0"](https://github.com/esphome/esphome-devices/pull/1494), whose
|
||
panel timings, pins and pitfalls this board file follows. The **CrowPanel *Advance* 7.0"** is a different board with
|
||
other pins (ESPHome's `CROWPANEL-ADVANCE-7` model); this file is for the plain CrowPanel 7.0".
|
||
|
||
## Files
|
||
|
||
- `packages/boards/elecrow-crowpanel7.yaml`: the board file (hardware, the 800 × 480 sizes, the flash measures); the
|
||
interface itself is `packages/core.yaml`, shared with both other boards (docs/PROFILES.md).
|
||
- `packages/elecrow.yaml`: what a screen builds from over GitHub; `elecrow-crowpanel7.yaml` in the root is the same for
|
||
a build from a checkout; `installers/elecrow.yaml` the block for a hand-written ESPHome configuration.
|
||
- `components/smart_display/elecrow_usb_phy.h`: frees the USB pins for the touch I2C (below).
|
||
- `components/smart_display/partitions.py`: the partition table that makes the firmware fit (below).
|
||
- `tools/verify_gt911.py`: physical pixel check, as on the Guition; no resistive calibration.
|
||
|
||
Choose **Elecrow CrowPanel · 7 inch** under **New screen** in ESP Screens (app 0.2.93+). The Guition's own parts (the
|
||
Rotation choice) stay off for it; everything the Guition can show, it shows.
|
||
|
||
## Interface
|
||
|
||
Six tiles of **378 × 108 pixels** per page in two columns, the Guition's rows and fonts across a wider page: the
|
||
vertical sizes are the Guition's to the pixel, the tiles and the cards take the extra width. The top bar, the tile
|
||
labels, the alert card (560 wide, its camera picture 532 × 220), the colour and climate titles and the page keys are
|
||
sized for 800 px; the cards that are a share of the page (the setpoint card, the mode keys) simply widen. A camera
|
||
opens full screen at 800 × 480; ESP Screens serves the picture in that box (`camera_feed.BOXES['elecrow']`).
|
||
|
||
At 133 pixels an inch the Guition's 42 px icons are a shade larger on this panel than on the 4-inch (170 ppi), which
|
||
suits a screen that stands further away.
|
||
|
||
### Touch
|
||
|
||
The GT911 is polled every 20 ms over I2C at 400 kHz, with no interrupt pin and no reset: the **V3.0** has a PCA9557
|
||
I/O expander (I2C 0x18) on the GT911's reset and interrupt lines, and writing it during boot is what breaks the touch
|
||
on that revision. It powers up with every pin as an input, a pull-up brings the GT911 out of reset before the firmware
|
||
starts, and the driver finds it ready. A bus scan at boot upsets the GT911 too, so `scan: false`.
|
||
|
||
The GT911 takes I2C address **0x5D** when GPIO 38 reads low at power-on and **0x14** when it reads high; on this
|
||
board it is 0x5D on most units, and a unit that never reports a touch may be a 0x14. Give that screen an Override YAML
|
||
in ESP Screens (Screen settings → Override YAML) with:
|
||
|
||
```yaml
|
||
touchscreen:
|
||
address: 0x14
|
||
```
|
||
|
||
**GPIO 19 and 20, the touch I2C, are the ESP32-S3's USB D- and D+.** The ROM leaves the USB PHY on those pads and
|
||
ESP-IDF's I2C driver cannot take them back: the bus reads as `I2C software timeout` and the touch never answers
|
||
(esphome/esphome#15356, ESPHome 2026.3+). `elecrow_usb_phy.h` runs before any component, as a static constructor,
|
||
and lets the pads go; it is behind the build flag `ESP_SCREENS_FREE_USB_PADS`, which only this board file sets, because
|
||
ESPHome includes every header of the component in every build and the Guition, an ESP32-S3 too, keeps its USB. The board's USB-C port is a CH340 on UART0, so flashing and the log are unaffected; the
|
||
`GPIO19 is used by the USB-Serial-JTAG interface` warnings at build time are expected.
|
||
|
||
### Rotation
|
||
|
||
A landscape panel with a layout 800 px wide: it does not turn. `ROTATION_SUPPORTED` is `false`, the settings page
|
||
shows no rotation row, and the app offers none for this board.
|
||
|
||
## Flash
|
||
|
||
The ESP32-S3-WROOM-1-**N4**R8 has **4 MB** of flash (the N4; 16 MB in the YAML boot-loops with no log). The firmware
|
||
is the Guition's, with camera images; with the Guition's fonts it is **2,028 KB**, and ESPHome's own partition table for
|
||
4 MB, two update slots of 1,792 KB with 448 KB kept for NVS, does not hold it. Three measures make it fit with room for
|
||
updates, all in the board file, measured with ESPHome 2026.9.0 (the add-on's):
|
||
|
||
| Measure | Saves | Where |
|
||
|---|---|---|
|
||
| Two update slots of **1,984 KB** and 64 KB of NVS instead of 448 KB (the preferences take a few KB; ESP-IDF's own two-slot example keeps 16 KB) | 192 KB more room a slot | `smart_display: partitions: 4mb_wide_slots`, `components/smart_display/partitions.py` |
|
||
| The four icon fonts (the 314 tile icons at 42, 26 and 18 px, the 31 big icons at 64 px) at **2 bits a pixel** instead of 4; the text fonts keep their 4 | 156 KB | `font:` in the board file (`!extend` on the core's fonts) |
|
||
| The TLS client only; nothing serves TLS | 7 KB | `sdkconfig_options` in the board file |
|
||
|
||
That is **1,865,456 bytes, 91.8 %** of a slot: within the CYD's rules (docs/RELEASING.md step 2), in the *tight* band,
|
||
and `tools/check.sh --firmware` applies the same budget to this board. Without camera images it is about 1,754 KB,
|
||
86 %: drop the `online_image`, `http_request` and `preview_camera` sections, the alert's picture frame and the
|
||
`camera_image_seed` image, and empty the camera hooks (`BOOT_CAMERA_HOOKS`, `BOARD_PAINT_FILL`, `CLOSE_CARDS_HOOK`,
|
||
`MAY_OPEN_EXTRA`, `TICK_HOOK`, `AWAY_EXTRA`, `ALERT_SHOW_HOOK`) as the CYD's board file has them. The icons at 4 bits
|
||
a pixel are the Guition's 156 KB back; they fit only without the camera images, and then at 94 %.
|
||
|
||
The partition table is part of the firmware and **never changes once a screen is flashed**: an update over Wi-Fi
|
||
writes into the other slot of the table the screen has, and only a USB install (ESP Screens' New screen, or ESPHome
|
||
Web with the factory image) lays the flash out anew. A screen flashed with this table keeps it through every update.
|
||
|
||
## Panel
|
||
|
||
ESPHome's `mipi_rgb` driver with the `RPI` model: the panel takes the pixels straight from the ESP32-S3's LCD
|
||
peripheral and needs no initialisation, so the timings are the whole configuration: 15 MHz pixel clock, inverted
|
||
(`pclk_inverted: true`, without it the picture tears), horizontal porches 40/48/13 and vertical 1/31/13, the 16 data
|
||
pins of Elecrow's schematic. The frame buffer is in PSRAM; LVGL draws in a buffer of 15 % of the screen, the same
|
||
number of pixels as the Guition's 25 % of 480 × 480.
|
||
|
||
## Checks
|
||
|
||
- `python3 tools/check_packages.py`, `esphome config elecrow-crowpanel7.yaml`, `tools/check.sh --firmware`.
|
||
- The touch test page and `tools/verify_gt911.py` for the corners; the ghost-touch filter at (0, 0) of the Guition's
|
||
GT911 applies here too.
|
||
- `diagnostics/capture_ui.py` saves the LVGL render at 400 × 240 (half the panel) as a PNG; `ui_self_test` renders
|
||
every card without touching a device.
|
||
- A build is not a flash, and a render is not a touch: the owner checks the picture and taps the corners.
|